Weak showers when someone opens a kitchen tap, water hammer and noisy pipes are often signs of pipes that are too small for the flow they carry. Choose a pipe and enter the flow it must deliver, and the calculator shows the water velocity, the pressure lost over each 10 metres and the flow the pipe can carry at recommended velocities.
Pipe Size and Flow Calculator
Velocity and pressure loss
Water velocity1.04 m/s
- Verdict
- Good: quiet, low pressure loss
- Pressure loss per 10 m of pipe
- 7.2 kPa (0.74 m head, 0.07 bar)
- Maximum flow at 1.5 m/s
- 28.8 L/min
- Maximum flow at 2 m/s
- 38.5 L/min
- Internal diameter used
- 20.2 mm
Friction is calculated with the Hazen-Williams formula for straight pipe; fittings, valves and bends add roughly 20–30% on a typical house run. Internal diameters are typical values and vary by class and manufacturer.
Recommended water velocities
For hot and cold water supply inside a building, keep velocity at or below about 1.5 m/s for quiet pipes, and below about 2–2.5 m/s at most. Higher speeds cause noise and water hammer, wear copper fittings and lose a lot of pressure. Long supply pipes from the meter or a borehole are often sized for even lower velocity, so that enough pressure is left at the far end of the house.
Typical pipe sizes in South African homes
| Pipe | Typical use |
|---|---|
| 15 mm copper / 16 mm PEX | Branches to single basins, toilets and showers |
| 22 mm copper / 20–25 mm PEX | Main runs through the house and geyser feeds |
| 25–32 mm HDPE | Supply from the meter to the house |
| 40–50 mm HDPE | Borehole, tank and farm supply lines, irrigation mains |
Old galvanised steel pipes corrode inside and narrow with age, so they carry less than their size suggests. Replacing them is often the fix for poor pressure in older homes. Compare copper, HDPE and PVC pipes.
Frequently asked questions
Is 15 mm pipe enough for a shower?
Will a bigger pipe increase my water pressure?
Get a free quote
Use the result in your quote request and a plumber or supplier in your area can price the job accurately. These services are related to this calculator:
Copper Pipes & FittingsGet a free quote on copper pipe and fittings: 15mm and 22mm SANS 460 tube, compression and capillary fittings, in single lengths or bulk, from local suppliers.
HDPE Pipes & FittingsGet a free quote on HDPE pipe and fittings from South African suppliers: 32mm to large-bore coils, PN ratings, compression and fusion fittings, bulk.
Plumbing SuppliesGet a free quote on plumbing supplies from a local merchant: pipes, fittings, geysers, taps, sanitaryware and plumbing tapes, from single items to bulk orders.
Pressure Pumps & Booster PumpsLow water pressure or a new tank? Get a free quote for a pressure pump or booster water pump, supplied and installed by an independent plumber near you.
More plumbing tools
Geyser Size CalculatorFind the right geyser size for your household, how long it takes to reheat and how much energy your hot water uses.
Geyser Electricity Cost CalculatorSee what your geyser costs each month and how much a lower thermostat, a heat pump or a solar geyser could save.
Water Tank Size CalculatorWork out how big a backup water tank you need for outages, and how much rainwater your roof can collect.
Water Leak Cost CalculatorFind out how much water and money a dripping tap, running toilet or hidden leak is costing you.
Household Water Usage CalculatorEstimate your home's daily and monthly water use, the cost on your bill and where the biggest savings are.
Drain Fall CalculatorWork out how much fall a drain pipe needs over its length, or check the gradient of an existing run.
Pressure Pump Sizing CalculatorWork out the flow and head a booster pump needs, so you can compare pump curves and quotes.
Geyser TroubleshooterChoose what your geyser is doing to see the likely causes, safe checks and how urgent it is.
